This has been one of the most involved projects we've worked
on so far but it has been totally worth it. After figuring out the look we were
after, my husband drew out a
plan of how to make it. Essentially, the library
consists of 5 cabinet bases, 5 bookshelf tops, and some trim to finish it off.
Since this is a built in library, we will talk about how we made it starting
with explaining how to build one bookshelf. If you have a larger or smaller
wall you would need to adjust accordingly. Here are the basic steps we
went through.
Tools we used:
- Table saw
- Skill saw
- Router
- Sander
- Craig Jig
- Air compressor
- Nail guns
- Screw gun
- Drill
- Wood clamps
Supplies we used:
- 2"x6" pine for the foundation
- 3/4” Birch cabinet-grade plywood for cabinets and bookshelves
- 3/16” laminated plywood for cabinet backing
- 1/4" barn siding plywood for bookshelf backing
- 3/4” poplar trim (various widths) for styles and rails
- Wood glue
- Screws
For the cabinet bases and bookshelves, we used ¾” birch
plywood (cabinet grade). For the trim and doors, we used poplar, which holds paint
well and is an easy wood to work with. For the bookshelf backing, we used
“barn board” plywood. For the cabinet backing, we used 3/16” laminated plywood.
We got everything from Home Depot.
To start, we removed the baseboard trim and crown molding in
way of the built-ins. Be careful when removing the trim because you’ll end up
re-installing it when the built-ins are complete.
The cabinet bases are made of 4 main pieces: the two sides,
the bottom, and a shelf. We used a router with a ¾” bit to carve out slots for
the bottom and the shelf. Our workshop is in our unfinished basement, which we plan to finish someday soon. Here is a picture of the main pieces prior to assembly.
We then assembled the pieces using glue and screws and then added a
spreader (the top horizontal piece) and finished it off by nailing a 3/16”
plywood backing to the cabinet. We did this 5 times.
Meanwhile, back upstairs we made a foundation out of 2"x6" pine lumber for the cabinet bases to sit on. We made the foundation height such that
the top of the installed baseboard trim would come about 1” below cabinet
bottoms. Then we set the cabinet bases on the foundation and re-installed the
baseboard. We then added poplar styles and rails to the cabinet bases.
The cabinet top is made of the same birch plywood with a ½”
baton of poplar to hide the end grain. The hole in the wall is where the wiring comes out. There was a switched outlet on the bottom left of the wall which we planned to use for power for the sconces.
The next step was to make the book shelves. We used the same
router bit to cut slots for each shelf. We made the shelf spacing 12”. We chose 12" based on the largest books we had and what we wanted to put on the shelves.
Then we assembled the pieces using glue and screws.
And repeat!
If you are going to do something similar, I recommend
painting the bookshelves BEFORE installing the backing. It will save you a TON of
time. The backs were made of barn siding plywood and is relatively inexpensive, but rough. However, once you sand it down, it looks amazing. On another side
note, while we were sanding, we had a crazy visitor. I have no idea what this
bug is called but it freaked me out. It was HUGE!
After the backs were sanded, we primed, painted, then nailed them to the back of the completed cabinets.Then we brought the bookshelves upstairs and put them on top of
the cabinet bases. The spaces between the book shelves are for the wiring.
The next step was to start adding the trim. We started with
the top rail. We made the top rail fairly wide because it would also serve as
the backing for the raised crown molding. Then we added the stiles (vertical
boards) which covers the bookshelf joints and holds the sconces. The lighting we got at
Overstock. At first we were looking at swing arm lamps that were gorgeous, but out of our budget; especially since we would need five. Then we decided on sconces since we would then only need four.
Nothing (not even this project) would stand
in the way of making our kids practice piano. That is why the piano never left
this space. We had to move it around quite a few times but it all worked out.
Then we added the rails for each shelf out of 1 ½” strips of
poplar and attached them using glue and nails. We then put the rest of the crown molding back up.
All that is left now are the cabinet doors. These were the
hardest part. My husband would write a whole post just about these doors but to
make a long story short, here is how we did them.
Each door is made of two stiles (the vertical pieces), two
rails (horizontal pieces), and a center panel. The slot in the middle of each
stile and rail was made with a table saw. The rails also have “tongues” (also made on a table saw) which
fit in the slot of the stiles. Here is the resulting frame prior to gluing it up.
We then glued the door pieces together and sanded.
We primed and painted each door in the basement before
installing them. We went with Blum Euro-style hinges from
Amazon which require
blind holes in one stile.
We also covered the entire built-in with a protective polyurethane coat.
We added the doors to the cabinets and added our kitchen knobs (we decided to put some pulls in our kitchen, so this was an easy way to re-use knobs we already had). You can see our library reveal post
here.
And then we took a nap.
***Updated March 3, 2014***
Here's how she looks now all decked out-
You can see my post on how I styled this beauty in
this post and the transformation with the sconces using Rub N' Buff
here.
.jpg)
.jpeg)
.jpeg)
.JPG)
.JPG)
.jpg)